Prices shown exclude VAT 

Ply Frame for KST X10 Mini, KST DS135, MKS HBL6625 Mini, MKS DS6125 Mini (pair)

Product Code: AW-X10-MINI
 (14 reviews)

Price: $3.87

More than 10 in stock
Add to basket to see shipping cost
Quantity

Description

These HyperFlight CNC cut ply servo frames make fitting a KST-X10-Mini, KST-DS135MG, MKS-HBL6625-Mini , MKS-DS6125-Mini or a similarly sized servo to a molded wing very easy. No thickness is added to the installation, and the servo is mounted securely, yet can be removed easily if required. Two servo frames supplied in the pack.

These frames are beautifully laser cut from 3.8mm plywood and include several 0.5mm ply shims (spacers) to go under the mounting lugs and correctly mount the servo.


How To Mount Wing Servos Using Ply Frames

1. Glue a strip of 3mm (or 1/8”) balsa to the leading edge of the mount (width dependant on the distance the mount is likely to be behind the main spar).
2. Place the mount with the servo in-situ in the wing and abut it against the rear of the main spar.
3. Slide the mount sideways until it is in the correct position laterally and determine how much the width of the 3mm balsa needs to be adjusted for the mount to be in the correct position fore and aft.
4. Trim balsa to size. Reposition servo mount in wing and when happy with position draw a pencil line around the outside of the mount.
5. Remove servo from mount and epoxy mount into wing taking care not to get any epoxy in the inside of the mount which will prevent servo sitting properly in the mount.
6. Set up and adjust servo control rods as required. When satisfied glue servo in position using silicon / bath sealer and allow to set overnight.

To remove servo gently lever out with a suitable small screwdriver, allowing time for the sealer to break its bond between the servo and the wing.

Do not epoxy the mount in place with the servo in-situ for two reasons. A) It gets in the way when trying to place the mount. B) It introduces side loads which have a tendency to move the mount out of position whilst the epoxy is setting.

To minimise control surface slop the servo must be mounted as rigidly as possible. In molded wings this is greatly assisted by bonding the servo to the bottom wing surface, using a suitably shaped wooden block. Similarly attaching false ribs to the inner and outer edges of the servo bay will mechanically connect the upper and lower wing skins, increasing rigidity.

Reviews 14  


 Review by:

ply frames for kst ds 135

don't think the frames are thick enough for the kst 135 servo, the servo sits below the frame to be glued in and need to be thicker for more purchase for the screw,
Speed of delivery and service second to none though.


 Review by:

Ply frames

It has been six weeks, still have not received these items. Unable to evaluate.


 Review by:

Ply frames

It has been six weeks, still have not received these items. Unable to evaluate.


 Review by:

Ply servo frames

Economical & handy frames makes fitting and removing wing servos much easier.


 Review by:

Not fit !!

These ply frames are too thick to fit with KST X10 mini. Prefer molded plastic frames.


 Review by:

Ply frames for MKS DS6125 Mini, KST DS135MG

These frames arexexcellent quality fit extremely well and make servo installation easier and more secure.


 Review by:

KST DS135 MG Servo Mount/Frame

Perfect fit for the KST DS135 MG Servo in terms of case outline etc.
The servos rubber grommet does lift the servo up fractionally from the frame on one side. But I always just file a recess into the frame around the lead exit hole anyway. A glue layer will usually negate any need for this. But just to make it clear. Very few servo recess mount locations are perfectly flat anyway.
Great service as always from the Hyperflight team.

Many Thanks As Always :-)


 Review by:

perfect fit.


 Review by:

Frames for D 6125 mini

Good fit for KST X10 mini.


 Review by:

These are excellent CNC cut frames and the MKS 6125 mini servos are a perfect fit. The predrilled holes did not line up exactly but this is not a problem as larger 2mm holes need to be drilled as pilot holes for the 3mm self tapping screws provided with the servo. Highly recommended for a slop free servo installation.


 Review by:

Easy fitting

Bought these for fitting KST 135MG. Secure and quick fitting


 Review by:

Wow ---they made it easy to fit the servos in the wing's
Saved me hours!


 Review by:

Wow ---they made it easy to the servos in the wing's
Saved me hours!


 Review by:

The frames were too thin. An extra 1mm had to be added so that the servos are not protruding out the underside.


Related Products 0

Shop Securely

Contact Us

HyperFlight
Drybank Farm
Fosse Way, Ettington
Stratford-upon-Avon
Warwickshire, CV37 7PD
United Kingdom
+44 (0) 7821 351341
447821351341
shoppingtest@itpartnership.com
Contact Form

Follow Us

facebook   facebook   twitter   Google My Business